Electric Built-in Cooktop
LOCATION REQUIREMENTS
PRODUCT MODEL NUMBERS
MEC7430W
MEC7536W
MEC7630W
MEC7636W
IMPORTANT: Observe all governing codes and ordinances. When installing cooktop, use
minimum dimensions given.
ꢀ
To eliminate the risk of burns or fire by reaching over the heated surface units, cabinet storage
Electrical:
space located above the surface units should be avoided. If cabinet storage is to be provided, the
risk can be reduced by installing a range hood that projects horizontally a minimum of 5" (12.7
cm) beyond the bottom of the cabinets.
If codes permit and a separate ground wire is used,
it is recommended that a qualified electrical installer
determine that the ground path and wire gauge are
in accordance with local codes.
ꢀ
ꢀ
The cooktop must be a specified cooktop that is approved to be installed either alone or over an
undercounter built-in oven. Check the cooktop base for an approved installation label. If you do
not find this label, contact your dealer to confirm that your cooktop is approved.
Ovens approved for this type of installation will have an approval label located on the top of the
oven. If you do not find this label, contact your dealer to confirm that your oven is approved.
Refer to oven manufacturer’s Installation Instructions for approval for built-in undercounter use
and proper cutout dimensions.
Check with a qualified electrical installer if you are
not sure the cooktop is properly grounded.
Make sure that the electrical connection and wire
size are adequate and in conformance with the
National Electrical Code, ANSI/NFPA 70-latest
edition or CSA Standards C22.1-94, Canadian
Electrical Code, Part 1 and C22.2 No. O-M91-latest
edition, and all local codes and ordinances.
ꢀ
ꢀ
ꢀ
The cooktop should be installed away from strong draft areas, such as windows, doors, fans or
strong heating vents. The cooktop should be located for convenient use in the kitchen.
Use the countertop opening dimensions that are given with these Installation Instructions. Given
dimensions are minimum clearances and provide 0" (0 cm) clearance.
Grounded electrical supply is required. See “Electrical Requirements” section.
Before You Make the Electrical Connection:
To properly install your cooktop, you must
determine the type of electrical connection you will
be using and follow the instructions provided for it
here.
IMPORTANT: To avoid damage, check with your builder or cabinet supplier to make sure that
the materials used will not discolor, delaminate or sustain other damage.
ꢀ
A 3-wire or 4-wire, single phase, 240 volt, 60-Hz.,
PRODUCT DIMENSIONS
AC only electrical supply is required on a separate,
40-amp circuit for 30" (76.2 cm) models or 50-amp
circuit for 36" (91.4 cm) models, fused on both
sides of the line. The model/serial number rating
plate is located on the metal cabinet underneath the
cooktop. See the following illustration.
B
A
C
A. 21¹⁄₂" (54.6 cm)
B. 30" (76.2 cm) models - 30" (76.2 cm)
36" (91.4 cm) models - 35⁵⁄₁₆" (89.7 cm)
C. 3³⁄₄" (9.5 cm)
CABINET DIMENSIONS
IMPORTANT: If installing a range hood or microwave hood combination above the cooktop,
follow the range hood or microwave hood combination installation instructions for dimensional
clearances above the cooktop surface.
A
A. Model/serial number plate
The cooktop is rated 240 volt and does not have a
A
D
ꢀ
neutral (white) wire.
ꢀ
The cooktop should be connected directly to the
junction box through flexible, armored or
nonmetallic sheathed, copper cable. The flexible,
armored cable extending from the fuse box or
circuit breaker box should be connected directly to
the junction box.
B
C
F
G
E
ꢀ
Locate the junction box to allow as much slack as
possible between the junction box and the cooktop
so that the cooktop can be moved if servicing
becomes necessary in the future.
A. 30" (76.2 cm) on 30" models; 36" (91.4 cm)
on 36" models
B. Combustible area above countertop (shown
by dashed box above)
C. 30" (76.2 cm) minimum clearance between
top of cooktop platform and bottom of
unprotected wood or metal cabinet
(24" [61 cm] minimum clearance if bottom of
wood or metal cabinet is shielded by not
less than ¹⁄₄" [0.6 cm] flame retardant
millboard covered with not less than No. 28
H
H
ꢀ
Do not cut the conduit. The length of conduit
I
J
provided is for serviceability of the cooktop.
ꢀ
A UL listed or CSA approved conduit connector
must be provided at each end of the power supply
cable (at the cooktop and at the junction box). A
listed conduit connector is already provided at the
cooktop.
ꢀ
If the house has aluminum wiring follow the
MSG sheet steel, 0.015" [0.04 cm] stainless steel, or 0.024" [0.06 cm] aluminum or 0.020"
[0.05 cm] copper)
procedure below:
1. Connect a section of solid copper wire to the
pigtail leads.
D.13" (33 cm) recommended upper cabinet depth
E. 2¹⁄₈" (5.4 cm)
2. Connect the aluminum wiring to the added
section of copper wire using special connectors
and/or tools designed and UL listed for joining
copper to aluminum.
F. 20³⁄₈" +/- ¹⁄₁₆" (51.75 +/- 0.16 cm)
G.18" (45.7 cm) minimum clearance from upper cabinet to countertop within minimum horizontal
clearances to cooktop
H. Junction box or outlet: 6" (15.2 cm) minimum from top of counterop; 7" (17.8 cm) maximum
from right side of cabinet
I. 29¹⁄₁₆" +/- ¹⁄₁₆" (73.8 +/- 0.16 cm) on 30" (76.2 cm) models 34⁹⁄₁₆" +/- ¹⁄₁₆" (87.8 +/- 0.16 cm) on
36" (91.4 cm) models
J. 1" (2.5 cm) minimum distance to nearest left and right side combustible surface above cooktop
Follow the electrical connector manufacturer's
recommended procedure. Aluminum/copper
connection must conform with local codes and
industry accepted wiring practices.
Because Whirlpool Corporation policy includes a continuous commitment to improve
our products, we reserve the right to change materials and specifications without notice.
Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specifications subject to change without notice.
Ref. W10274255A
10-06-09
|